Had new kitchen furniture installed recently, well the installers I guess didn't pay attention to this floor strip thingy (IDK the name in english) and now it sits curved up, it's ugly and dirt gets under it.

I tried glueing it down with VERY strong glue, but the underside of it isn't flat enough to get a good grip with the floor, it stays glued for a few hours and pops back up.

Is there any way to fix it that doesn't involve moving the furniture? It's installed in place and cannot be easily moved.

Hopefully the photo shows what I mean.

Edit: I got pissed off (sue me, I got hit by a car today and I'm in pain and a bad mood) and knocked over the furniture on the right. Well even without it, the stupid thing STILL stays curved. Please someone tell me how to fix this.

How can I get this out? Please help me

Trying to disassemble my bed but this screw is stripped and I need a 90 degree ratchet just to reach it. Anyone have any ideas on how to get this out?

Hello all, I’m having trouble tracking down this style of weatherstripping for the door that leads from the house to the garage. It’s t-shaped and fits into the groove cut around the inside of the frame. House was built in 1980, I had to remove the door to sand and paint and replace all the hinges and trim etc. The weather stripping looked crusty as hell so I need to replace it but all stuff I’m finding is for newer style doors and I really don’t want to just use a peel and stick. Any help to find something that is like the original would be very appreciated, tyvm

This Halloween prop is supposed to have the skeleton pop out when a sensor goes off. A kid broke it by forcing the lid closed last year. Now, when the lid tries to open, it gets stuck in a short cycle, like maybe the teeth on a rotating mechanism can't catch. Idk if that's what's happening though; I'm going to have to disassemble it to see what's going on. Any ideas on how to fix?

ADDITIONAL PHOTOS IN COMMENTS

Hi everyone,

I have a tilt-and-turn window in my room, but when I close it, there’s some play on the side of the handle and the upper part, and the window doesn’t sit completely flush against the frame. As a result, more noise gets in, along with a bit of wind. Is there a way to tighten the window’s locking mechanism? (The mechanism uses a spring-loaded plate along the side, and there are corresponding plates on the frame, I’m not sure what these are called.)

Thanks to anyone who can help me with this!

I purchased a floor model Frigidaire French door unit five years ago from Lowe's. The doors have never swung shut by themselves and have been driving my nuts ever since.

Although I have done many refrigerator repairs, I had no knowledge of closer cams. In researching, I see that the door lifts slightly when opening, and then the oposite to self close. I will assume that the original assembly left these out, as I see nothing like a cam in there.

Are there two halves, or what? any help with this is appreciated.

This door is about three years old and randomly the lock popped off? How do I fix this? It looks like it should just screw back in but it didn’t when I tried (granted it was kinda quickly as I have two toddlers running around.)

So our garden hose rusted off inside the thing that attaches. Any ideas about how to get this attachment off will be greatly appreciated

Hi all. A relative’s blinds fell down about a year back and revealed this beneath it. One thing lead to another and repairs got put off time and time again, and at this point im not sure where to start.
My question is who should I even contact to fix it, and what can I do in the meantime? Apologies if this is a no-brainer! im totally new to this and out of my depth…

Good day everyone,

I just assembled this long office desk (about 87in) made from particle board from Wayfair, but I don’t want it to sag in the middle when my girlfriend and I start adding monitors and other things on top. I’ve never owned a table this long, and I’d like it to not sag in the middle. There are 4 metal beams running under the desk, 2 on each side, but there’s no metal legs. I’ve attached the pictures to this post.

My questions are:
How likely is it to sag?
What can be done? (I dont have a lot of tools beyond a drill and a handsaw)
How much time do I have before it starts sagging?

Greetings all, currently restoring a car interior and this veneer around my radio is bothersome. You can see the separation of the clear finish from the veneer above the manual switch and I was thinking about ways to fix this without totally stripping it and putting new clear coat on. I can separate this plate from the head unit to work on, and I was planning on finding some kind of glue I could inject that would dry totally clear to bond it. The little cracks everywhere don’t bother me as much but eventually I may fix it 100%.

yeah we got it second hand. but its loose, like when u grip some "white things" it comes out from the nail.

i believe its made from thin plastic pipe, and iron rode as the main up to down support.

i feel like fi we proceed with nails, its not gonna stand to long since there are alot of holes in the plastic itself

My chair ripped and I have no idea how to fix it 😭😭😭

The problem is that the hole gets bigger and bigger!

My mom had this oil spray bottle and really loved it. Today while cooking I placed it a bit hard on the counter and broke it. Is there any way I can fix it because the hole looks pretty fixable and it doesn't have any other cuts. I can't buy a new one because it is not available where i live.

Size of hole: ~3.5cm

Material: Glass

I have a 3D printer but the only materials available are PLA and PETG but I dont think they are good for pouring oil/food items.

Please help because my mom is really mad at me.😔

Got home with a piece I really liked and found that inside one of the drawers was some unknown damage. It's warped like something spilled in it, with this white powdery crystally stuff on it, and smells like sour whiskey? Smelling it gives me a headache.

Before I start trying to clean, is this something I should be triple cautious around? Any advice on cleaning/restoring? Do I need to replace/rebuild a drawer?

Im working on a Rixon number 36 concealed door closure. Which the internet says doesn’t exist. Tennant has said that one of the doors slam shuts. One of the doors doesn’t close at all. I have tried looking for any sort of closure or latch valve adjustment. Can’t seem to find one. Only things I can find is the park open mechanisms (knob and prongs with wire). I’ve done some digging on the Interwebs. I find that the adjustments could be under the rail system. so I tried to take it apart. Well the dang thing won’t come apart, even though I’ve removed the two screws holding down the top railing. I don’t want to force it apart and bend the railing.

I’m hoping for the needle in the haystack chance that someone has worked on this model before.